SD3813UV light-curing shadowless adhesive, UV glue is the best curing wavelength


SD3813UV light-curing shadowless adhesive is a kind of adhesive that must be cured by ultraviolet light irradiation, it can be used as an adhesive, and can also be used as a rubber compound for paints, coatings, inks, etc. UV is the abbreviation of Ultraviolet Rays in English, that is, ultraviolet rays.

 

 UV light-curing adhesive application


It is mainly designed for the bonding and fixing of various electronic components and glass and plastic substrates.

 

 UV light-curing adhesive pre-curing product performance

 Appearance - light yellow, transparent viscous liquid


Viscosity (@25°C, rotational viscometer) - 3800~4500mPa·s

 

 UV light-curing adhesive curing conditions


SD3813 cures under sufficient UV exposure, and its speed and depth depend on the light intensity, the spectral distribution of the light source, the irradiation time, and the light transmittance of the adhesive material. The following data were measured under UV radiation of 20 mW/cm2 from a high-pressure mercury lamp:

 Positioning time (S) – 10

 Deep curing time (1mm, S) - 35

 Full curing energy – 500 mJ/cm2

 

 Product performance of UV light-curing adhesive after curing


The following data were measured after curing with a cumulative energy of 500 mJ/cm2 from a high-pressure mercury lamp source:

 Hardness (Shore D) - 73~78

 Coefficient of thermal expansion (/°C) – 8.2×10-5


Bonding substrate (1 cm2) – Bond strength (kg/cm2)

 PC/PVC ——≥3

 Stainless steel/GLASS – ≥3

 

 UV light-curing shadowless adhesive weather resistance test


The following data were measured after curing with a cumulative energy of 500 mJ/cm2 from a high-pressure mercury lamp source:

 substrate

 Test conditions

 Bond Strength Retention (%)

 PC/GLASS

 65℃ 90% RH (72H)

90

 PVC/GLASS

 65℃ 90% RH (72H)

90

 Stainless steel/PVC

 65℃ 90% RH (72H)

92

 Stainless steel/GLASS

 65℃ 90% RH (72H)

92

 

 How to use UV light-curing shadowless adhesive and precautions


One of the two objects to be bonded is transparent and the surface is clean, dry and grease-free;


Apply UV adhesive to one of the surfaces, close the two planes, and irradiate with a UV lamp or a high-pressure mercury lamp with a suitable wavelength (usually 365nm-400nm) and energy, from the center to the periphery, and confirm that the light can indeed penetrate the adhesive part;


It is recommended that when the light is about 6s and the initial positioning is carried out, the remaining glue on the workpiece should be removed and then re-illuminated to complete curing;


The curing time should be different according to different preparation materials, adhesive thickness, and UV intensity. It is recommended that users purchase an ultraviolet intensity tester to test the light intensity before bonding to reduce the scrap rate;


The temperature also has a little effect on the activity of the glue, and the curing time should be appropriately extended when the temperature is low;


The material to be bonded should not be squeezed and repeatedly rubbed during operation, and it is recommended to use fixing tools;


When bonding plastics, the content of ultraviolet absorbers in plastics should be considered, as high content will seriously affect the transmittance of ultraviolet rays, which will also have a significant impact on the curing efficiency of the glue, and even cause the glue to fail to cure;


Low-viscosity products are recommended for large-area bonding. If the conditions are available, it is best to purchase vacuum equipment and laminate in a vacuum environment to remove bubbles and improve the yield rate;


The above instructions are for reference only, and the specific operation needs to be adjusted appropriately according to the specific situation.

 This product is not dangerous goods, but do not enter and eyes.

 

 UV light-curing shadowless adhesive packaging, storage and transportation requirements


Transportation: There are no regulations for domestic (CN-GB) and international (IMO, IATA, UN). It is a non-dangerous good.


Packaging: (1) The packaging of the material has a certain protective and sealing effect on the material to ensure that the material is not damaged during transportation.


(2) The packaging box should have product model, name, quantity, manufacturer's trademark, production batch and other information.

 (3) The packing box should meet the requirements of moisture-proof, shock-proof, pressure-proof and mildew-proof.

 


Storage: The products packed into boxes should be stored in a cool and dry environment below the ambient temperature of 28 °C, and there should be no acidic, alkaline or other corrosive gases in the surrounding air, and under the above conditions, the storage period can be 12 months from the production date, and the materials are still qualified within these 12 months.

 Packing: 250ml, 1kg

 

 UV light-curing shadowless adhesive statement


Users must carefully read the relevant information of this product before using this product, and it is the user's responsibility to conduct a comprehensive test according to their respective uses to confirm its performance, effect, safety, etc.


We disclaim any other warranties stated or implied. If the product is unqualified due to the direct use of your company without the corresponding performance test, the company and the intermediate sales legal person do not assume any responsibility, hereby declare!

Product description


Key words:

Related products

undefined

undefined

Get free product quotes

Our staff will contact you within 24 hours (weekdays), if you need other services, please call the service hotline: 0752-6822862
%{tishi_zhanwei}%